Questions tagged [power-transmission]

The tag has no usage guidance.

13 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
36 views

Optimum spoke shape for wheels made of solid material

Currently I am designing a bicycle sprocket to be laser-cut out of 3mm steel. Steel is heavy, so I want to make some lightening cut-outs, and I want to optimize the shape of the cutouts. I will ...
2
votes
0answers
25 views

I'm looking for the simplest way to increase rotational speed from 120 to 5,000 rpm for a light duty device

I'm currently designing a device and want to increase speed from 120 to 5,000 rpm. Device is lightweight, hand operated, free spinning, low torque in/out. Picture a cheap fertilizer spreader from Home ...
2
votes
0answers
32 views

Exceed 'designed' speed ratio of timing belt

I'm trying to create a setup to transfer motion from a motor to a shaft that requires a much higher torque (bi-directional). The housing is about 6 inches long and the speed ratio needed will be ...
2
votes
0answers
129 views

How do I calculate the velocity of the piston?

I have a system with a motor connected to the trapezoidal lead screw. The lead screw is connected to the tube which is connected to the piston. The piston has to pump 1000cc oil against a pressure of ...
1
vote
0answers
29 views

What are the limits of small 3D printed gears?

How much tangential force should I expect a 10~20mm pitch diameter/1.5mm gear module 3D printed rack and pinion system to support without breaking nor sliding?
1
vote
0answers
18 views

Is there any way to simulate belt transsmition with non-circular cog?

I want to do a simulation of a transmission with toothed belt and elliptical gear. I've tried in Autodesk inventor by modeling wheels separately and then adding a belt with the "synchronous belt tool" ...
1
vote
0answers
29 views

Bevel gear friction and inertia calculation

I want to calculate the friction and inertia between 2 bevel gears with straight teeth. I know how to calculate those parameters between regular gears with straight teeth. Is there any difference for ...
0
votes
0answers
27 views

How does tractor achieve constant PTO speed?

Tractors have a PTO shaft which supplies power to implements. Most implements are rated 540 or 1000 RPM. I'd like to know more about transmission that is used to convert variable motor shaft rotation ...
0
votes
0answers
43 views

Could railway overhead wires be used for long distance electricity transmission?

Most electrified railway in Europe operates at 15 kV 16.7 Hz AC or 25 kV 50 Hz AC. Power is typically produced between about 2.3 kV and 30 kV and stepped up to 115 kV to 765 kV AC for long distance ...
0
votes
3answers
132 views

How does ferranti effect occur?

I search and read about Ferranti effect online, but none seems to be clear enough for me to understand how it actually happens. I must say, I do not have much prior knowledge about inductive/...
0
votes
0answers
83 views

Can you use a flex (spider) coupler as a dog clutch in a motorbike/atv/go kart/lawn mower like setting?

My question is simple: I want to make a dog clutch system for a wakeboarding cable system and was wondering if a flex (spider) coupler could used? The power, velocity, torque is similar to a go kart /...
0
votes
0answers
41 views

Why are there no fully diesel electric cars?

Diesel electric locomotives seem popular, even these days. The UK's Type 45 destroyers have tried integrated electric propulsion, and I think that there are hybrid motor-generator cars that can ...
0
votes
1answer
255 views

Equations for power transmitted by a flat belt drive

I've come across two equations that relate power transmitted with the belt tensions: $$\begin{align} P &= 10^{-3}(T_1 - T_2)(k)(v) \\ P &= 10^{-3}(T_1 - T_c)(k)(v) \end{align}$$ As you can ...