Questions tagged [pipelines]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
1answer
87 views

Pipe network analysis: static pressure of a closed-loop pipe

I've learned fluid dynamics but does not have much knowledge about its real-world applications. My question is about the static pressure of a closed-loop pipe. [Fig. 1. Pipe network. Source: ...
3
votes
1answer
431 views

Negative head in Darcy's flow equation

This question appeared in my midterms. A pipe transports water from a storage tank A to storage tank B. Storage tank A is at an elevation of 20 m above B, the pipe length is 6.4 km. The present ...
7
votes
4answers
1k views

Why is the friction factor in laminar flow independent of pipe roughness?

The Darcy friction factor is defined as: $$f_D =\frac{64}{Re}$$ with $Re$ I mean Reynolds number (global). I was wondering why Darcy in laminaire flow is independent of pipe roughness (wall roughness)?...
2
votes
1answer
763 views

What are the differences between compressor stations, pump stations, and booster stations?

I am doing some research on impacts related to natural gas compressor stations. In some states, I've received data for compressor stations alongside other facilities in the oil and gas world. These ...
1
vote
2answers
572 views

Find Torque and Force on Pipe with Bend

I did a Civil Engineering course some years ago and from my textbook I had a question on a pipe with a bend. Now I think I have the part of the question on force correct, but I am not sure how the ...
0
votes
2answers
128 views

Straight Pipe Thread

Is there any National Pipe Thread Straight (non-tapered, requires O-ring or compression olive) that is compatible, even loosely, with a machine thread threaded rod? I want to put a reducer on the end ...
0
votes
2answers
123 views

Assessing flow rate from open sea into a container

I'm currently assessing sub sea pumped hydro capabilities, and need to use the flow rate in order to calculate power output. I can calculate the energy storage capacity using E = mgh: $E=mgh = ...
0
votes
2answers
34 views

Question on fluid flow measurement uncertainty

Say you are trying to measure the liquid flow rate (mass or volume) through a pipe and you want to get the best measurement possible, and you have two flow meters. In one scenario, you put one flow ...
0
votes
2answers
79 views

Pumps' geometric similarity

Given two pumps that are similar : $H_1=70-1.41x10^{-3}Q_1^2$ $H_2=100-1.1x10^{-3}Q_2^2$ Find the geometric scale : $\frac{D1}{D2}= ?$ I am also given maximum efficiency = 1. I tried solving but I got ...
1
vote
1answer
45 views

Why is the head loss in submerged pipe is 0

Looking at this question : Point C head loss is 0 according to the author Bottom right Can’t understand why , any good explanation for this claim ? Look at page 33 at the top
1
vote
1answer
48 views

Calculate mass flow rate of saturated fluid through pipe

Its very basic question. But there is no data all over internet about it. Let's see how we calculate mass flow rate through pipe. We take velocity of fluid and c/s area of pipe. Then we find volume ...
0
votes
1answer
68 views

How do you determine flow distribution at a dividing T-Junction?

So I've been trying to find out how to determine what proportion of fluid will flow down a given path when a main line branches into two lines at a 90 degree T-Junction and I can't find anything ...
0
votes
0answers
28 views

Inspection chamber in sewage drain

For civil engineers, There is a high drain connection work is under progress in my location. Few days ago, a contractor visited my house and asked me to construct 2ftX2ft inspection chamber inside the ...
35
votes
2answers
17k views

What is the purpose of these diversions in a natural gas line?

The campus where I work has a long covered walkway (~.5 mile) which has several labeled pipes running under the roof (chilled water, fuel oil, air...). All of the pipes run dead straight except for ...
0
votes
2answers
151 views

Shearing Stress at the Boundaries of two infinite Planes

This is a worked example on a book I am reading (Fundamentals of fluid Mechanics). He then asks "Can you explain the change in sign? [Hint: Sketch a sheared fluid particle adjacent to the top ...
2
votes
0answers
71 views

Calculate fan power

I was wondering how to calculate the required fan power for the following air pipe network. Other losses besides friction is not calculated for. Known parameters: Fan provided flow, VA = 3000 m3/h ...
-1
votes
1answer
177 views

Head loss for T junction diverging water pipes

I am writing to ask for help with a T-junction pipe problem. Attached picture shows the pipe configuration. The schematic shows a large pipe with ID 16.5mm and smaller 4mm ID tubes connected to it. ...
8
votes
2answers
6k views

How Can I Determine Multiple Discharges from a Pipe Network? (Knowing the Inlet Conditions)

I have little/no experience with pipe networks and have been searching for a methodology to calculate the discharge from multiple outlets of an oil pipe network with a single inlet. As far as i can ...
-1
votes
1answer
323 views

Pipe Invert Elevation

Can someone please help and explain if the invert elevation of the pipe is calculated as 192+2+10? or 192+2+10+0.6667 (8" pipe)? Or 192+2+10+1 (measured to bottom)? Sketch is not to scale.
0
votes
0answers
51 views

Leakage detection system along the pipe

I want to design a leakage detection system along the pipeline that will use differences in pressure of flowing liquid (change in pressure between two points). Which sensor I should use?
4
votes
2answers
68 views

Divide Flow and Maintain Pressure

Im in the process of building an espresso machine from readily available parts. I have a solenoid pump that supplies pressurized hot water to the coffee grounds. I want to be able to tune the pressure ...
-1
votes
2answers
35 views

How to design internal wall separation in the PVC tube to use it as a water tanker

I am working on design of the column which contains the water tanker and the pump + electronics at the bottom. I have tried different solutions and they failed. I would like to know your advice on ...
2
votes
1answer
130 views

Determining required pressure drop for choked flow conditions to be met

I have pipework system with an inlet pressure, $P_0$, which passes from a pipeline of fixed diameter, $D_0$, through a tee with reducer to a smaller diameter pipe, $D_1$, before returning to another ...
10
votes
2answers
1k views

What is the maximum length of oil pipelines?

This is inspired by the discussion and controversy surrounding the Keystone Pipeline. The main part of the Keystone Pipeline system is about 3,400 kilometers long, stretching across a large portion ...
0
votes
1answer
79 views

Airsoft BB Funnel Design - Electric funnel jam solution?

I'm working on a design to feed Airsoft BB's through a funnel. A simple gravity fed system (ie. I don't want to force them out at speed) but every now and again the BB's get jammed at the end of the ...
2
votes
3answers
141 views

How do you determine how many pumps you need in a pipeline?

I am working on a pipeline design scenario and I am trying to determine how many pumps I need. In addition to this diagram, I'm given a flow rate range and an acceptable velocity to also determine the ...
1
vote
0answers
3k views

Calculating discharge on the pipe diameter and the pressure?

Is it possible to сalculate discharge / flow rate on the pipe diameter and the pressure (for constant pressure)? For example: Pressure_internal = 5 bar, ...
-1
votes
1answer
41 views

What are the simplest available methods for monitoring pressure and airflow in a 22mm diameter pipe?

In the emergency case that more than one person must share a mechanical ventilator, the medical professionals lose per-patient monitoring of pressure and airflow. To that end, what are the simplest ...
1
vote
1answer
24 views

Linear pneumatic actuator opening time - pressurise connection pipe

I would like to estimate the time needed to open a linear single-acting pneumatic actuator. The actuator's piston is loaded with a spring pushing downwards and the operating fluid (air or nitrogen) ...
2
votes
1answer
32 views

Heat Loss through a run of insulated piping

I've been racking my head around calculating the amount of heat loss still water will experience through a run of insulated piping. The water in the tank is maintained at roughly 550°F saturated, and ...
0
votes
1answer
2k views

Calculating the flow rate of a siphon system

What i am looking for: I am looking for a formular to calculate the water output in $l/s$. My goal is to match a pump (pumping the water back up) with the following setup, to keep it going with as ...
0
votes
0answers
54 views

Finding Horizontal and Vertical Force on Bending Pipe

I did a Civil Engineering course some years ago and from my textbook I had a question on a bending pipe. The purpose of this question is to see if the way that I have calculated this is correct, as ...
22
votes
3answers
1k views

How to know whether the flow is supersonic in a nozzle?

For a project I had built a convergent divergent nozzle designed for Mach number = 3. In that project, I could know the flow has gone supersonic by seeing the manometer fixed between the throat and ...
7
votes
3answers
13k views

Force required to empty a syringe

How would you go about solving the following problem. I believe Bernoulli's equation needs to be employed, but I'm not sure how. Find the magnitude of the force that needs to be applied to a piston ...
1
vote
0answers
98 views

Trying to simulate the bending of a right angled pipe in solidworks

I have created a bent right angled tube in solid works. It has a constant inner diameter of 1" and thickness of 1/8". The tube is comprised of a straight portion 1 ft in length, followed by a 90 deg ...
0
votes
1answer
120 views

Determining the headloss according to Darcy-Weisbach with pipes in parallel and series

Given the following situation: Pipe A and B have a known and identical length and diameter, and are in parallel. I'm assuming the flow trough pipes A and B are also identical, as is the roughness of ...
0
votes
0answers
77 views

Ideas on optimization of DRA and energy consumption of a pipeline

I have a 200 mile pipeline with a few pump stations in between. I am trying to find ways to optimize the electricity and DRA consumption, and was wondering if anyone has ever done something similar ...
1
vote
1answer
41 views

Volumetric flow in a pipe from velocity

I think I'm missing something important here. For a fluid with a velocity $u$ in a pipe with cross section area $S$, the volumetric flow rate is equal to: $$Q_v = uS$$ If we now consider vectors, ...
4
votes
3answers
86 views

How to make sure a pipe does not take all of the water from a stream?

I am trying to design a pipe which takes water from a river and transports it to a reservoir. However, I do not want my pipe to take all of the water from stream, because that will create all sorts ...
1
vote
4answers
76 views

Software options for simulating oil flow in small diameter pipes [closed]

I'm looking for 1D software packages that can simulate flows of oil (lubricant) in pipes of a small diameter (typically between 1mm to 12mm in diameter) and have found around 10+ possible candidates, ...
2
votes
1answer
85 views

Connect heated copper tube in PVC tube

I have a copper tube that I'm heating (quite a lot) with a torch, I have to connect a PVC pipe in the entrance of the copper and one in the exit (so water can flow through the copper pipe). The only ...
1
vote
0answers
134 views

Determining the Steady Discharge Between Two Reservoirs

A uniform pipeline, $5km$ in length, $100mm$ in diameter and with a roughness size of $0.03mm$, conveys water between two reservoirs. The difference in water level between the reservoirs is $...
3
votes
4answers
15k views

Water pump at top floor or bottom?

Which position of the water pump in the below diagram provide maximum water output to the overhead tank? Each floor is 12 feet in height. I already have the pump (Centrifugal Regenerative Self ...
0
votes
1answer
44 views

How to create an algorithms for fitting a network of tubes into a cube? [closed]

How to create an algorithms for fitting a network of tubes with a range of diameters into a cube, with maximum volume in the tubes? Assume: 30 cm minimum square side 1 cm minimum pipe diameter 1 mm ...
0
votes
1answer
79 views

How to maintain a static negative pressure in a valve?

My target is to create a valve with multiple inlet capillaries. And my output is a pipe of a larger diameter. I do not want to use any electrical systems, and at the same time, I want to maintain ...
1
vote
1answer
244 views

Simple way to duct a PVC pipe through a stainless steel sheet cover

I need to duct a PVC pipe (DN80) through a stainless steel sheet metal covering. The hole thing needs to be tight against stormwater. There's tons of products to duct pipes through thick walls, but I'...
1
vote
1answer
64 views

Do nylon and rubber bushes usually come in sizes between steel pipe sizes?

I'm in Cambodia where I don't speak the lingo and I'm hoping to do a little DIY project. If I were to buy two different off the shelf steel tubes am I right in thinking that the most common nylon and ...
8
votes
2answers
234 views

Heating circuit: Galvanized steel with press fitting vs welded steel pipes

What are the downsides for galvanized steel pipes + press fittings vs. welded steel pipes in a heating application? Diameter would be DN25/1". Background: The customer specifies only steel, only ...
4
votes
0answers
90 views

Simplifying head loss across a piping network

I am tasked with designing a compressed air piping network,with and would like to determine the pressure loss across the different layers of instruments -now here is the 3D layout of the network. ...
0
votes
1answer
184 views

Equivalent Lengths of Pipe for Laminar Flows

I have a pipe network with laminar flow (peak output from the pump gives a Reynolds number around 1100). I have some test data for the network and the results are really odd to me; I cannot explain ...