Questions tagged [meshing]
The meshing tag has no usage guidance.
14
questions with no upvoted or accepted answers
2
votes
2
answers
553
views
How to determine the deflection of a wire mesh under wind load?
I am trying to extend a metal wire mesh over a large distance, while tensioning it to limit the deflection of the mesh due to the wind as much as possible. After doing some research I came across ...
- 21
2
votes
0
answers
141
views
Airfoil meshing using ANSYS
Logged in a little time ago i have a new question. So I am trying to mesh an arifoil geometry using ANSYS meshing. Airfoil number is NACA 84-M profile. Running 2-D simulation my main objective is to ...
2
votes
1
answer
421
views
Trouble with Base circle and meshing with spur gears
I am a novice who is trying to make some gears. I have followed the formula's but sadly something seems to go wrong and the gear's don't come out right. Below is some dimensions and pictures.
Gear 1
...
- 21
1
vote
0
answers
19
views
My ANSYS model meshing is showing problem where I don't see my model and small blue rectangle appears. Is there any way to solve this?
I'm new to ANSYS and just started using it. I encountered a problem when I click the model option; ANSYS Mechanical opens, but there is this blue rectangle, which is supposed to be big and show my ...
1
vote
0
answers
160
views
How to export 'simplified' geometry from Simulation workspace in Fusion 360 to ANSYS Mechanical?
I would like to export the defeatured version of my design to ANSYS.
I tried adopting the following methods but they weren't working out.
(https://forums.autodesk.com/t5/fusion-360-design-validate/...
1
vote
1
answer
871
views
Meshing Complex models in abaqus
I'm trying to mesh a model of a morphing wing in Abaqus and have been running into issues. It was recommended that I partition the model into smaller parts, but it seems that the more I try to ...
- 11
0
votes
0
answers
19
views
Ansys Mechanical Section Plane Error
I'm attempting to make a deformation analysis for a specific scenario in Ansys Mechanical. Everything seems to be fine, but when I try to use a section plane, the deformed region appears to be 'hollow,...
0
votes
0
answers
18
views
Error message in ANSYS Fluent setup
While trying to run a simulation in ANSYS Fluent, I am getting this error message : Error at Node 0: Normalized key of 26982 is out of range [0, 27030]. This error message comes when I try to run the ...
- 1
0
votes
0
answers
17
views
How to preserve edge grading of rotated edges in ICEM CFD?
I have a 2D axisymmetric geometry for which I am generating block-structured mesh in ICEM. I am converting this 2D block setup to a 3D block setup by rotating the 2D blocks using a dedicated option in ...
- 1
0
votes
0
answers
24
views
Hexamesh of a helical coil in ICEM CFD
I am trying to mesh a helical coil segment in ICEM CFD. My approach is to create a 3d block at the start of the geometry, and then extrude it along the center curve:
However, when I do this I end up ...
- 101
0
votes
0
answers
198
views
Can one connect Starlink router with the Mesh via ethernet cable?
I know that with the Starlink ethernet adapter one can connect to the router or mesh with the ethernet cable.
My question is: is it possible to connect Starlink router with the Starlink mesh via ...
- 101
0
votes
0
answers
51
views
Structured trianglar finite element mesh in MATALB
The available triangular mesh in the MATLAB PDE tool box here gives an unstructured triangular mesh.
How can I get a structured triangular mesh from the tool box with a similar data structure [p,e,t]. ...
- 101
0
votes
0
answers
127
views
Workbench Ansys Mesh Convergence study
Is it possible to perform a mesh study using Ansys?
So I want to change the mesh size, and show the effect of this on my solutions, any suggestions?
- 1
0
votes
0
answers
106
views
Marching Voxel FEA Mesh
I'm working on an FEA model and my mesher uses a "Marching Voxel method" I'm wondering what the relationship is between mesh size and computation time is? I.e. if I half the mesh size (1mm to 0.5mm) ...
- 632