Questions tagged [injection]
The injection tag has no usage guidance.
13
questions
0
votes
0
answers
5
views
Assisted mixing in devices like steam injectors
In steam injectors in particular good mixing is not that important I assume. But in fuel burners mixing is very important. If we would make a gas-gas injector, that would use low pressure so that ...
0
votes
1
answer
92
views
Why would these hydraulic cylinders have 3 large connections?
I am trying to work out how a recently acquired Arburg 220-90-350 from 1982 works so that I can build a new control system and get it working. It's a direct clamping machine with no toggle.
The ...
0
votes
0
answers
34
views
How to get this hydraulic system working and help identifying parts and their function
I have recently acquired a 1982 Arburg 220-90-350 injection moulding machine, mainly just as a hobby to further my knowledge on injection moulding machines and control systems as I plan to modernise ...
1
vote
1
answer
36
views
Designing an injection molding mold for a part with a certain parting line and ejector pin location
How do you design a mold to create that part? The only way I can think of is to make the parting line horizontal to the part instead of vertical. But is there any way to design the mold so that the ...
2
votes
3
answers
91
views
Prototype for Injection Molding
Mold for Injection Molding is very expensive and is justified for mass production.
However, at Prototype stage, how we make the same part with less expensive method. I know 3D Printing is a way but ...
0
votes
1
answer
46
views
Injection nozzles and static mixers for LSR - How do i prevent an uncleanable blockage between runs?
I'm trying to implement a new material in our processes, and that's a 2 part, highly viscous (500-1000 Pa s) liquid silicone rubber. I will also be adding a pigment, so that's 3 components that need ...
6
votes
1
answer
972
views
How are non-continuous internal threads plastic injection molded?
I'm trying to figure out how the heck some of these plastic bottle caps are injection molded. By having the thread on the inside of a cap, this obviously creates an undercut.
Now I've watched some ...
3
votes
1
answer
74
views
Designing a Chilled Process Water System for Small Plant
I am designing a new, closed loop,chilled water system for our small injection molding outfit and can use some help where to begin. Here are some of my knowns:
Northeast NJ, USA, no air conditioning. ...
1
vote
0
answers
14
views
Shear between which two fluids is better for atomisation - liquid & liquid or gas & liquid?
In designing an atomizer which generates a spray of liquid, one can adopt atomisation through shear.
Shear in the following cases are to be considered:
stagnant Gas- moving Liquid: in this gas case ...
1
vote
0
answers
26
views
Injection and lose of fluid injected and pressure drop down? [closed]
I am trying to develop a field by using water injection.
I am facing a problem that the average reservoir pressure is dropping down and the BHP of the production wells dropping down as well until it ...
2
votes
1
answer
137
views
Combustion Chamber Back Pressure due to gas injection
I am trying to calculate prior to testing the expected back pressure resulting from injecting gaseous oxygen through an injector orifice (choked) into a rocket combustion chamber before ignition. I ...
0
votes
1
answer
54
views
Material Properties of ABS
I've been working on a design that requires a plastic snap feature. I've assumed up to this point that the material will be injection molded ABS, with material properties I pulled off of matweb.
...
1
vote
1
answer
120
views
Plastic Vacuum Cleaner Part -- Why did they design it this way?
I've designed a whole lot of different parts and products in my time: Plastic, metal, lighting products, electrical products and automotive parts. I generally can look at a product and figure out why ...