Questions tagged [applied-mechanics]

Questions about using applied mechanics to model engineering problems.

Filter by
Sorted by
Tagged with
0
votes
0answers
41 views

Solving Hertz Impact ODE with Simulink

I have a question about modelling a nonlinear 2nd order ODE for an impact of a sphere on a thin plate in Simulink. Depending on the solver and solver options, my results in Matlab vary a lot. Some are ...
0
votes
0answers
67 views

Need help with FEA bar analysis problem

I'm trying to solve this which is to find the total deformation of the bar. I'm trying to implement the finite element approach, but I am getting way too large of numbers. Here is what I did in ...
0
votes
0answers
32 views

Stopping metallic construction held by a threaded rod from wobbling

I am working on a 1.5m satellite dish with a custom feed. The problem is that the feed is being very wobbly once slightly pushed, as shown here: https://www.youtube.com/watch?v=rAFGbEhhDZ8 (it swings ...
0
votes
3answers
273 views

Polarity of a relative angle - Knee joint angle

I'm wondering if it's correct to write: $$ \alpha = \theta_{lg} - \theta_{th} $$ EDIT: the theta angles are defined positive in counter-clock direcction, instead alpha in clockwise direction. My ...
0
votes
1answer
101 views

Installing satellite dish to point to local zenith

After receiving help on my previous post (Stopping/reducing wobbliness in threaded rod), I've decided to come back and ask another question: how can I actually hold the satellite dish into place? I ...
0
votes
0answers
33 views

How to slide 2 small pieces of metal into each other

I'm trying to build a keyboard addon for my smartphone (https://gitlab.com/xengi/mkbd65). The last challenge I'm facing is how the two pieces, namely the smartphone and the keyboard should slide back ...
0
votes
1answer
62 views

Soil mechanics-Geotechnical engineering [closed]

Which is more economical to improve or change the soil that is used to build a structure? my answer is that it depends on each case, but I would like to get more information, or where to search about ...
0
votes
2answers
62 views

Polyurethane mix-on-the-spot system

3d printing is a slow process and for my solution I need fast printing. So I print with no infill and I fill inside with a two part, 10 min drying polyurethane resin. I mix them in a disposable cup ...
0
votes
1answer
66 views

Analytic expressions of the kinetic and potential energy [closed]

A homogeneous rigid circular disc (radius R, mass ms, center point S) rolls without a slip on a plain with a small angle of inclination alpha against the horizontal. A point mass MG is fixed on the ...
0
votes
1answer
462 views

I need to determine the RPM of a rotating cylinder over which a silk thread is wound and is moving along in the fashion of a screw.

Recently I visited a sericulture facility in India and I saw that people there 'degummed' (https://www.youtube.com/watch?v=h13fctiTylI) silk in a batch process. As a Chemical Engineer, I thought of ...
0
votes
1answer
83 views

Finite Element Code: Convergence issues

I am trying to code a simple FEM problem. A bar is fixed at the bottom edge, and a displacement is applied at the top. I want to apply the displacement gradually , so I have divided it into a number ...
-1
votes
2answers
34 views

How to design internal wall separation in the PVC tube to use it as a water tanker

I am working on design of the column which contains the water tanker and the pump + electronics at the bottom. I have tried different solutions and they failed. I would like to know your advice on ...
-1
votes
1answer
115 views

Could a spinning permanent magnet's interaction with the Earth's magnetic field propel a boat through the water?

I am wondering if a spinning permanent magnet's interaction with the Earth's magnetic field will produce a propelling force strong enough to propel a toy boat through the water. This propelling force ...
-1
votes
2answers
142 views

Does a change in specimen dimension affect the measured yield strength and tensile strength?

I am having a hard time trying to understand the effect of geometry on a specimen's yield and tensile strength or if there even is one. If there is an effect or not, why is it so? Thanks in advanced!
-1
votes
1answer
58 views

Equation governing relative motion between aircraft and store

I am reading a paper titled Conditions for safe separation of external stores by EE Covert [Link]. In Section 1 Introduction of the paper, the author has given an expression for $d$, the relative ...
-1
votes
1answer
51 views

What theories solve the problem of weight dispersion to minimize damage?

I assume there's some simple link to give me to answer this, but I don't know the terminology for it and so haven't been able to solve this. The use case it to avoid having my TV put divots into my ...
-1
votes
1answer
18 views

Effect of speed of turbo fan in bypass jet engine

Why do we keep speed of turbofan of turbofan jet engine, low. And what is the maximum thrust a turbofan jet engine., how much can thrust a turbofan jet engine produce with just compressed air.
-1
votes
2answers
181 views

From a mechanical point of view(Physics/Engineering) why are Front-Load washers said to clean/wash better than Top-Load washers on average?

Which cleans better? Is it just marketing or do they really clean/wash better due to some physical property or the way they work, I am asking how do they if they do? N.B I do not intend to indicate ...
-1
votes
1answer
23 views

A sealed ball is not connected to anything externally, but can have any complex mechanism inside. Can the mass change? [closed]

A sealed ball is not connected to anything externally, but can have any complex mechanism inside (mechanical, chemical, or any other). Can a wireless trigger from a remote or any other wireless ...
-1
votes
1answer
52 views

Deriving equation of motion of a 1 degree of freedom system

Before solving this system, note that the rigid bars $\mathrm{\overline{OA}}$ and $\mathrm{\overline{OB}}$ are rotating about point $\mathrm{O}$, not their respective CGs. To account for this two ...
-1
votes
1answer
35 views

Door functional or not? [closed]

Hello I am building a door and I have taken a large rectangle piece of wood for the base. At the top-right point of the rectangle I am planning to connect it with the top right point of a large ...
-3
votes
1answer
148 views

diy drone w/ carrying capacity of 7lbs? [closed]

I want to build a drone that can carry around 7lbs. Is it possible to make a drone that can carry that much weight using electric motors without it being over /$500?
-4
votes
1answer
66 views

Improvised weighing machine from broomstick and 1kg counterweight [closed]

Let's say I want to measure the weight of a bag of clothes (or some other object), in a situation where I don't have a weighing machine ("scales"?) available. Objects that are available: A broom. ...

1 2 3 4 5
6