Questions tagged [applied-mechanics]

Questions about using applied mechanics to model engineering problems.

Filter by
Sorted by
Tagged with
0
votes
3answers
38 views

What will be the force F for the given brake system?

I am getting two ways to find F. One is Fx0.2=30 Nm which gives F=150N Other is Fx0.2-640x0.13=0 which gives F=416N I am confused which one is incorrect. I know problem is too basic but still not ...
4
votes
1answer
84 views

Determine the aceleration of points B,C and D, angular aceleration of rod and the tension in rope DE when ropes AB suddenly breaks

The solutions are F(DE)=134.38N, a(D)=2.016m/s^2 , α=1.29rad/s^2, a(C)=7.828m/s^2 I agree that the FBD and the KD are these: Then to solve this problem I've done: $$\sum M_{c}= I \alpha_{BCD}$$ $<=...
0
votes
3answers
159 views

Force and the reactions on the supports

Consider the movement in the vertical plane of an $AB$ bar with a mass of $20 kg$, $0.8 m$ long and supported by two cursors: one at the end A and the other at point G coinciding with the center of ...
1
vote
3answers
52 views

Can I create a whirlpool/vortex around a horizontal axis in a flat bottle using motor?

I am using this flat bottle: I fixed a motor at the centre of one of the flat sides and attached an impeller. I thought this will create some kind of whirlpool effect but as you can guess, since the ...
2
votes
0answers
28 views

Bar released from upright position rotates about a lower hinge before being caught by a steel cable, how to calculate the tension on the cable?

I wish to check the safety factor of a steel cable that I've designed to catch a heavy bar that rotates freely due to the gravitational force acting on it. From the upright position, I'm assuming that ...
0
votes
2answers
29 views

Do tensile and compressive forces have significance only in pairs?

In strength of materials, there are two types of axial forces which can act on a prismatic bar - Compressive and Tensile. Do they significance only in pairs?
0
votes
1answer
68 views

Why is the theoretical formulation not explaining why the graph of the square of the velocity and angular displacement is nonlinear (experimentally)?

So I did a wind tunnel experiment where I put a rope restrained (1 degree of freedom, so it can wave in the direction of the wind) at one end so that it displaces according to the variation in wind ...
1
vote
1answer
70 views

Calculate Rolling Resistance Experimentally

I am trying to calculate the exact rolling resistance ($F_{rr}$) of my car. The approach I am going with is a coastdown test at a low speed so no drag slows down the car. From there I am going to ...
0
votes
3answers
38 views

Find the maximum stress at a point in a machine member

A machine member having a diameter of 50 mm and a length of 250 mm is supported at one end as a cantilever subjected to different forces as shown in the figure. Find the maximum stress at points A and ...
0
votes
4answers
320 views

Polarity of a relative angle - Knee joint angle

I'm wondering if it's correct to write: $$ \alpha = \theta_{lg} - \theta_{th} $$ EDIT: the theta angles are defined positive in counter-clock direcction, instead alpha in clockwise direction. My ...
0
votes
2answers
62 views

How long does it take and how far does it travel a sphere in free fall before reaching a percentage of the terminal velocity?

Assume a sphere (hail) that is free dropping in air. At some the sphere will reach close to the terminal velocity. The question is: how long $t_p$ in seconds does it take before a percentage $p$ of ...
1
vote
1answer
34 views

Does the terminal velocity of a sphere in free drop increase with increasing diameter?

I was trying today to calculate the terminal velocity of a hailstones with increasing diameter and mass. I was trying to figure out if larger hailstones will have a higher impact velocity or lower. I ...
0
votes
1answer
122 views

Break loose torque calculation of lock nut against rotating/acceleating bolts?

I have a Scenario where my lock nut is tightend using a prevailing torque of 14 Nm (as mentioned by the manufacturer) on to the rotor placed between bearings (But the tightening direction and the ...
0
votes
1answer
93 views

Alternatives to sawstop technology

Sawstop table saw braking system works by putting a low voltage on the blade, and when it detects that voltage shorted to ground, the blade is retracted and slammed into an aluminum block. The claim ...
0
votes
2answers
104 views

How to calculate traction force w.r.t. rotational speed of a shaft mounted at a certain angle on a surface?

I am designing a new mobile robot platform and i need a generic solution for the robot in order to establish a proper mathematical modeling. My question is about calculation of the traction force of ...
1
vote
1answer
51 views

Why this torque is not considered into the virtual work principle equation?

In the picture above you can see a SCARA robot, with its end effector (the point x,y). The torques c_a and c_b are the ones of the motors in the joints, while f is an external force. My teacher has ...
0
votes
0answers
26 views

Computing forces and moments acting on the sides of a rectangular shell element from corner forces and moments

I have a FEM program for shell elements implemented through the direct stiffness method. Using this program corner displacements of shell elements due to external loading are obtained through the ...
1
vote
0answers
50 views

How is a plank able to stop a spring door [closed]

So , here we have door which can get closed on its own due to spring. Agenda of Q is to put sth beside the door so that the door does not close . The Q tells us that when we put a brick of 0.5kg. Door ...
2
votes
3answers
86 views

Would a car slip down on a frictionless banked road and situation for friction road

Here , we have a car on a banking road. Considering two cases : Frictionless and friction surface of the road. I give an initial velocity to the car by a push for a second. Then , the cases discuss ...
1
vote
1answer
110 views

Installing satellite dish to point to local zenith

After receiving help on my previous post (Stopping/reducing wobbliness in threaded rod), I've decided to come back and ask another question: how can I actually hold the satellite dish into place? I ...
1
vote
0answers
26 views

Difficulty in understanding polarization? Is it only applicable for H and an electronegative element like chlorine? [closed]

There are two examples I have taken in diagram. In the first one , we have a cation and anion. They form an ionic bond due to which the cation has no electrons and the anion has 2 electrons. There are ...
1
vote
1answer
69 views

How to calculate torque required to rotate assembly about the center

The image is a hollow cylinder: 2in OD, 1.76in ID. Connected is an angled bracket, 45 deg, that weighs 3lbs. The top rectangle piece connected to the bracket is 10 lbs,the dimensions are 31.1in x 14....
0
votes
2answers
88 views

Can a beam be too short to experience bending stress?

The question in the title says it all. I've got a a configuration where I'm using a bolt to support a load. The way its set up, the bolt will have a very short cantilever on it. When I calculate the ...
1
vote
0answers
31 views

what is the torque difference in single plate clutch disks and multidisk clutches? [closed]

I have a review question that I am not sure about the answer. The question goes like this: "In comparison to single plate clutches, multidisk clutches are associated to which of the below notions?...
1
vote
1answer
64 views

How to generate a repeating semi-circle waveform using a mechanical linkage

How can one, in a smooth way, produce a semicircle wave, as opposed to a sinusoidal wave ? Imagining the machinery and linkages behind the movement. I mean the trace. For example a point fixed in ...
0
votes
0answers
56 views

Mounting grinding wheels on a threaded rod

I'm trying to mount a set of 6" grinding wheels on an M12 threaded rod. The problem I have is keeping them perpendicular to the rod so that they don't wobble when they turn. The wheels have a 1&...
7
votes
2answers
2k views

How do suction cups work?

These are suction-mounting hooks. I want to visualize and understand how do they stick on walls. After these hooks stick on wall. Like we compressed them. How? Since gases are compressible up to a ...
3
votes
1answer
66 views

Differential Equation for: Locking a laser's frequency with a PI controller

I think I have a good understanding of differential equations, so I would like to first try to understand my system in terms of differential equations before transforming my system into the more ...
0
votes
1answer
44 views

Low-Flow Nozzles for Corrosion Spray Testing

So, for a cyclic corrosion test system, I need a nozzle or arrangement of nozzles that provides a flow rate of 45ml-140ml of salt solution per hour to an area 60cm square. All commercial nozzles I've ...
3
votes
1answer
370 views

press fit ball joint

I enjoy creating mechanical designs but I am not a trained mechanical engineer. I have a technical issue with a joint design that needs to be permanently retained using a press (snap) fit. Any idea ...
3
votes
1answer
62 views

How do rollercoaster designers calculate the ideal curve?

I've been looking into rollercoaster track designs and wondered how they mathematically calculate the ideal curves to fit some specific layout without creating excessive Gs or other rider discomfort ...
1
vote
3answers
100 views

How can you control the speed of a rope moving through a pulley?

I'm putting together a ceiling-mounted clothes rack. The rack is raised and lowered with rope and pulleys. If the rack is raised under full load and accidentally released, then the system could be ...
0
votes
1answer
54 views

Find a constraint relation for this Q of 3 pulleys and 2 blocks attached with string

Using any method find the constraint relation between mass 1 and mass 2. Assumptions: No friction , massless string and pulley. Q: Find constraint relation between 1kg and 2kg block. what I tried so ...
2
votes
1answer
62 views

Free body diagram of a differential-drive mobile robot

I'm trying to study the free body diagram of this differential-drive mobile robot in case of straight trajectory (same torque applied on both of rear wheels) and pure rolling motion I started ...
2
votes
3answers
190 views

Do all structures deform if put a load on them?

Suppose I have a concrete wall in front of me and I push on it, now it seems that I do work and the energy has magically disappeared. I am trying to figure out how this works, the explanation I ...
2
votes
1answer
79 views

Generating Linear Velocity Movement?

In preparation for a Fluid Mechanics experiment, I am looking for a simple commercial ready made apparatus to generate a linear velocity trend to prove a new theory: https://aip.scitation.org/doi/abs/...
1
vote
1answer
47 views

Calculating the diameter of screws that are on radius 160mm from axis of rotation. I need help - I don't know If I'm thinking in the right way

First of all, english is not my first language so if there are some mistakes I made - I'm sorry and I hope everything is understandable. The example I am trying to solve reads the following: The gear ...
1
vote
3answers
129 views

Why do we write T cos theta = mg for this Q instead of mg cos theta = T

For this Q , the author of the textbook writes that T cos 45 =mg but it also states that mg cos 45 is not equal to T. I got to know about this because this is the way , I solved it first. My Q :1 is ...
0
votes
2answers
54 views

Effect of centripetal acceleration on angular acceleration

$a_t$ = $\frac{dv}{dt}$ = $\frac{d(r*\omega)}{dt}$ = $r $* $\alpha$. $a_c$ = r*$\omega^2$ = $\frac{v^2}{r}$ These are almost all the variables and values associated with centripetal and tangential ...
0
votes
3answers
55 views

How to guess direction of friction in any case

Here , in case of a death well situation as an example. Q How is direction of friction going to be opposite to mg or in upwards direction ? Why not: In case of like circular turning , direction of ...
0
votes
3answers
73 views

Different results when applying equation

The system shown in the Figure is guided by two blocks in A and B, that move in the fixed grooves. If the speed of A is 2m/s down, determine the speed of B at time θ = 45º In the textbook they said w ...
2
votes
1answer
201 views

Determine the angular velocity and angular acceleration of the AB bar at the instant shown

Consider a sliding cursor C that is fixed to the disk which has a constant angular velocity counterclockwise at 4 rad/s. Determine the angular velocity and angular acceleration of the AB bar at the ...
1
vote
2answers
59 views

What size feet for this wind-protection panel?

I need to create a series of free-standing perspex panels to add height to an existing fence for wind-proofing purposes. My idea is that each panel would be fixed to two supporting poles that are ...
0
votes
3answers
38 views

Is there any frame of reference in which we can neglect the gravitational force?

There is a laboratory in which there is a string tied to a bob on the earth.Consider the earth is perfect sphere ,rotates on its own axis in a circular path with uniform angular velocity. Main Q of ...
2
votes
1answer
50 views

Degree of freedom of a mechanism

A mechanism popped up in my mind when I was studying kinematics, see picture below $J1,\ J2,\ J3$ are rotational joints and there are two translational joints $J4$ and $J5$ between two sliders and the ...
1
vote
3answers
80 views

Why do I get pushed back when I’m in a car at high speed?

When I’m in a car at high speed , I get kind of like pushed back if I’m sitting on the cars seat. How does it happen and why ? If I’m in a car , then I have the same speed as car and for the car , I ...
0
votes
2answers
55 views

Find minimum horizontal force required to keep the block and wedge stationary?

In the adjoining figure, the coefficient of friction between wedge (of mass M) and block (of mass m) is μ. Find the minimum horizontal force F required to keep the block stationary with respect to ...
0
votes
3answers
95 views

How to solve this Question regarding compound accelerations

So , I was trying to solve it. Then , I notice that acc of 2kg mass has 2effects. One acc from the force to left and one from the Question , it says acceleration to be up. Then , the 2kg mass would go ...
2
votes
0answers
37 views

Magnetic Force - Point of Load

I am using a Magnet like this in an assembly and I am trying to calculate the torque in point P2 (see picture below) resulting from the attraction force F between my magnet and the steel part. As I ...
0
votes
2answers
52 views

Why is the acceleration of wedge and block equal like this

No friction at all anywhere. Let me explain the diagram in steps and the Q. green colour let us start with. It represent a wedge on which there is mass of 10kg (red colour). That’s it the first ...

1
2 3 4 5 6