Questions tagged [aluminum]

The tag has no usage guidance.

14 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
32 views

Is having a keyway in aluminium for 30Nm a bad idea?

I'm designing an aluminium shaft hub for a 16mm keyed shaft with a maximum torque of 30Nm. However, stress analysis tells me that the keyway can suffer too much stress: If my understanding is correct,...
2
votes
0answers
27 views

Aluminium plate being used in an AUV

I am currently using a AI-6061-T6 plate measuring 750mmx370mmx6mm as a rack between two frames at about 3/4 meter above ground. The load on the plate would be about 8-12kg. How much load will be able ...
2
votes
0answers
102 views

Standard parameters for machining aluminium?

Sorry for the weird question but I was wondering about the standard machining parameters for Aluminium (if there is even a standard). Particularly the values for a CNC process (preferably in SI) for a ...
1
vote
0answers
12 views

How to repair stripped, leaky pneumatic fitting?

I have a pneumatic cylinder with a stripped fitting, which causes a slow leak. I took it to a machine shop and he tried to re-thread it but there wasn't enough good metal left to get a good thread. He ...
1
vote
0answers
42 views

How do I to connect aluminium profiles with 60 and 120 degree angles?

I would like to construct an aluminium profile frame which includes connections with stiff fixed angles at 60 and 120 degrees. What options do exist for creating those connections, preferably without ...
1
vote
1answer
54 views

Mounting outdoors camera using aluminum 5052

I designed a simple U shape 2mm sheet metal bent mount for a 4kg outdoors CCTV camera. The mount was accidentally produced from 5052-H32 Aluminum instead of 6061-T6. Is it common to use 5052 ...
1
vote
0answers
38 views

Small scale aluminium tubes manufacturing

Our startup needs short aluminuim tubes (max. ~70 cm [~27.5 inches] long / less than 1 cm / 0.4 inch diameter) such as these: We'd prefer to manufacture them ourselves rather than buy them from a s ...
1
vote
0answers
661 views

How to straighten an aluminium extrusion?

The extrusion shape is a simple square tube. If I set it down on a perfectly flat surface with its curvature upwards, the middle raises up by around 5mm over the length of 1m. So far I tried to just ...
1
vote
2answers
97 views

What would happen if I tempered aluminum of aeronautical use (Al 2024)?

What would happen if I tempered aluminum of aeronautical use? Being more specific, an alloy of 96% of aluminum and 4% of copper, without modifications and 2% of impurities. (Al 2024)
1
vote
1answer
77 views

Tapped thread maximum load

I am building a stair from aluminium to go to my basement, the stair sides-plates are made from 10mm thick aluminium AWS 5454. I am planning to tap M10 thread into this plate. To avoid the step ...
0
votes
0answers
13 views

Should I use ST or LT values for extruded rod?

In MMPDS for AA7075-73511 (extruded rod) the Table 3.7.10.0(g3) show both ST and LT values for transverse directions. For a rod with circular cross section there is really no Short and Long transverse ...
0
votes
1answer
35 views

How to properly fit almuminum glass window without leakage?

I got a brick-wall house. The wall is 25cm thick. I want to add windows. There are 2 ways of adding a window: Adding the window on the inside side of the wall, so that if the aluminium frame of ...
0
votes
0answers
31 views

How to produce aluminium powder by E. J. Hall method

I have watched videos on YouTube producing Aluminum powder by mechanical methods. Like this one. It uses Aluminum foil and coffee grinder: There are similar videos which use the same basic method but ...
0
votes
0answers
96 views

Building bed out of 8020 aluminium extrusion

I want to build a rock and roll bed out of 8020 aluminium extrusion, in order to avoid the bother of welding steel pipe. However, I don't have much of a 'feel' for how strong this stuff is. Will ...