# How is the long-term creep of a spring determined?

Spring Design

In spring design, there a a variety of parameters to consider. Some of the parameters are solely physical (wire diameter, coil diameter, length, etc.) and some are determined from the physical dimensions in combination with the material properties (spring constant, allowable stress, etc.).

Spring Set

One physical characteristic of a spring is whether or not it will experience set. This is a permanent deformation of the spring after it has been compressed. Whether or not set is an issue depends on the level of stress that the spring undergoes versus the material's tensile strength.

The common rule of thumb is that set is not a concern if the spring only experiences 40% or less of its tensile stress. If the spring experiences between 40% to 60% of its tensile stress, then the set can be compensated for during manufacturing. Above 60% of the tensile stress, set cannot be controlled.

The reason that spring set can be compensated for is that it occurs after only a few cycles and then the full amount of set has been reached.

Creep

Creep is a separate phenomenon from set. Set happens immediately, but creep happens with constant load over time. Since the metal is under stress, it should exhibit creep. Creep is also affected by temperature.

I want to know how a spring is affected by long-term constant load. I have not been able to find any information about creep in springs or how to calculate it during spring design.

How is the long-term creep of a spring determined?

## Your question is insufficiently constrained.

The short answer is that you haven't provided enough information to give a complete answer: creep is complicated enough for a single material, however there are a variety of mechanisms depending on the material, temperature, normalised stress, time etc etc. In a "generic metal" the below diagram is a fair place to start for determining which mechanism you are working with, but those breakpoints will still change with the material. Obviously something like aluminium stops behaving like a solid metal well below 3000 deg C.

Some nickel superalloys experience less creep at higher temps, although these are exotic and extremely expensive.

If your question truely is "How is this determined for a specific spring of a specific material?" then the answer is disappointingly simple: put your spring in a constant temp oven for a range of very long times and a range of loads and measure what happens. It doesn't matter by which mechanism it is creeping, all you want to know is how it will respond in time to that load at that temp.

Edit: following your comment I feel I understand that what you are asking slightly better so should revise the answer accordingly. Whilst it is always best to test your parts creep is particularly nasty in that you can't get your answers quickly and it tends to be expensive. A material would help more than anything else here, but here is a suggested design method (I am not familiar with the design of springs to alleviate creep, this is just a common sense set of suggests from a fellow engineer):

1. Decide yourself the operating conditions you expect it to take: load, duration of load and temperature. You ought to know this all.
2. (optional) Decide what kind of spring response you want and design the spring accordingly. Different springs respond to load fundamentally differently.
3. Find some equation for estimating the stress distribution in a spring; you haven't specified what type of spring you are designing but based on the mention of compressive load I would assume a steel coil spring but it could be one of many. If that is the case then I don't have an equation for the stress distribution, which is likely to be complex as coil springs probably have a combination of axial and shear loads when they deform. Either way, find some stress distribution, I'd imagine because of continuity a mean stress would do which at first glance would just be a function of angle of coil relative to direction of compression.
4. Decide whether creep is seriously a consideration for you. Most springs operate no where near the UTS of the material they are made from and if you are orders smaller then I'd question whether creep is something you need to worry about at all. Your car sits on its springs for decades and doesn't lose appreciable ride height. Even if you do get some change, does it influence on your design at all if your spring grows fractionally shorter over the space of a decade?
5. Decide on how important weight saving is to you and choose your material to give you the desired spring constant whilst reducing cost as best you can.
6. Use a table similar to the one below to find the region of creep which you are operating in, given the material, and calculate your rate of creep from an equation which applies to that region and constants appropriate to your material. You can find this all online.
7. Figure out whether this rate is acceptable.

Please consider that the first step that one would take to alleviate creep (decreasing the normalised stress) will change the characteristics of your spring which likely restricts you to a material change or a different spring design.

• I agree that if I was asking for a specific number, the answer would be that more information is needed about material, load, temperature, time, etc. If I am reading your answer correctly, you are saying that there is no way to know (or estimate) how a given spring is going to react to sustained load. Therefore I need to design one and then test it. – hazzey Apr 1 '15 at 18:14
• Answer expanded. – thepowerofnone Apr 1 '15 at 19:04
• Just to throw a few more complications onto the fire: If the spring undergoes repeated load cycles, especially if they are alternating compressive and tensile stress, you probably have a situation involving a mix of "creep", "plasticity", and "fatigue" (scare quotes indicating the simplified text-book versions of each phenomenon). Also, springs may be made from non-metallic materials. If this is important, you most likely need to do some computer modelling using material behaviour models validated by testing, or do a realistic long-term test on the actual spring. – alephzero Apr 3 '15 at 4:01