Engineering

Notable Question

 Notable Question
Question with 2,500 views. This badge can be awarded multiple times.
Awarded 1148 times.
Stress Concentration Factor
Awarded 2 days ago
Technical drawing for a part with complex (non-line, non-arc) geometry
Awarded Sep 21 at 0:20
What are the materials most transparent to microwaves?
Awarded Sep 19 at 15:09
How to calculate failure stress on a hollow pin loaded in shear
Awarded Sep 18 at 14:26
How to calculate saturated steam flow rates?
Awarded Sep 18 at 2:28
What does 'Open Flow' mean for a pump flow rate?
Awarded Sep 18 at 2:28
What to do to increase the hp of a gx-160 engine?
Awarded Sep 16 at 21:20
How to do gold plating on Anodized aluminum and stainless steel?
Awarded Sep 15 at 20:52
How to find Performance assessment (IAE and ISE) of a PID Controlled system?
Awarded Sep 10 at 17:21
In case a plane stalls, what should stall first, the tip or the root of the Wing? Why?
Awarded Sep 10 at 11:49
Statics problem: Finding resultant force angle measured counterclockwise from positive x-axis
Awarded Sep 9 at 0:18
Forged carbon fibre finish
Awarded Sep 8 at 5:16
Why are earthfills fully covered in concrete where they join bridges?
Awarded Sep 6 at 17:06
What is really meant by HW/SW integration?
Awarded Sep 5 at 20:55
Clamping force of a bicycle quick release skewer
Awarded Sep 5 at 16:32
What kind of signal is the signum function? A power signal or an energy signal?
Awarded Sep 4 at 17:37
What is the formula for deflection of an end-loaded cantilever rod beam?
Awarded Sep 2 at 20:04
Difference between ACI Code and Eurocode in Stiffness modifiers?
Awarded Sep 1 at 13:21
Does perfectly elastic and perfectly plastic material make any sense?
Awarded Aug 31 at 21:56
What is the difference between mass moment of inertia and area moment of inertia? And why mass moment of inertia alone used for kinetic rotation?
Awarded Aug 31 at 15:55
Driving many parallel shafts from one motor
Awarded Aug 28 at 15:52
How to create a logic circuit that multiplies two 4 bit numbers, using only 16 2-input AND gates and 3 4-bit adders?
Awarded Aug 24 at 5:25
How to calculate the flow rate of a gas through a pipe?
Awarded Aug 23 at 15:40
Postion of overturning moment for retaining wall
Awarded Aug 23 at 0:20
Force in a crank system
Awarded Aug 22 at 15:02
Series O-ring in Vacuum Application
Awarded Aug 16 at 21:31
Material thickness to withstand Pressure
Awarded Aug 15 at 1:16
How to Plot Stress Contours in Abaqus?
Awarded Aug 13 at 11:32
estimating the surface area of a steam coil immersed in a tank
Awarded Aug 9 at 6:36
Why aren't gravity batteries everywhere?
Awarded Aug 7 at 19:34
Can I use a threaded bolt to support a ball bearing?
Awarded Aug 6 at 1:04
Creating a "half dome" in solidworks
Awarded Aug 1 at 23:30
Wrap a geodesic dome with a poly sheet: Minimize overlap & loose areas
Awarded Jul 31 at 8:26
What is the capacity of a WWII Submarine battery in kWh?
Awarded Jul 27 at 19:48
How to number section and detail view for a same drawing
Awarded Jul 26 at 18:57
What is the unit of measurement of fatigue damage in a structure?
Awarded Jul 25 at 18:00
Why are Whitworth threads angled at 55°?
Awarded Jul 20 at 4:02
How can I create uniform laminar flow in a short duct?
Awarded Jul 19 at 21:37
Solidworks: Make a copy of a sketch on a different plane
Awarded Jul 18 at 21:45
Block diagram vs flow chart?
Awarded Jul 17 at 13:19
Proof load for screwing into aluminium plate
Awarded Jul 14 at 20:31
What does 50% RH mean?
Awarded Jul 13 at 15:05
Design a worm gear that works with a straight wheel
Awarded Jul 10 at 9:40
Plastic modulus
Awarded Jul 8 at 6:02
Countersink bolt vs. Socket Head Cap bolt
Awarded Jul 6 at 23:25
Best way to attach a square tube to a flat surface?
Awarded Jul 6 at 21:48
Using a pattern of features as datum BOTH individually and as a group, for different FCFs
Awarded Jul 5 at 12:05
Why home Air Conditioning AC compressor insulated
Awarded Jul 4 at 6:27
How can I approach the application of control theory to real control systems?
Awarded Jul 3 at 13:16
Difference between maximum shear stress and absolute shear stress
Awarded Jul 3 at 6:27
Finding the mass in the tank of an air compressor from gage pressure
Awarded Jul 3 at 1:40
Heat transfer Calculation, for Cooling for an aluminium box
Awarded Jul 2 at 8:46
Why did the Plexiglass on the Bathyscaphe Trieste crack?
Awarded Jun 25 at 22:49
How determine the compression of a beam with a concentrated end load in the x axis?
Awarded Jun 25 at 12:25
Calculating the von mises stress in a 3D beam when given stresses and moments on both ends
Awarded Jun 23 at 4:30
How to measure a bearing temperature in a pump?
Awarded Jun 20 at 22:25
Torque and power for elevator with counterweight
Awarded Jun 15 at 11:33
What happens if we operate a positive-displacement pump in parallel with a centrifugal pump?
Awarded Jun 14 at 7:30
When calculating the deformed radius of a pressurized thick-walled cylinder, why is the hoop strain used rather than the radial strain?
Awarded Jun 9 at 15:03
How to determine the compressor power in a refrigeration system?
Awarded Jun 8 at 11:15
1
2 3 4 5
…
20

Your privacy

By clicking “Accept all cookies”, you agree Stack Exchange can store cookies on your device and disclose information in accordance with our Cookie Policy.