Engineering

Popular Question

 Popular Question
Question with 1,000 views. This badge can be awarded multiple times.
Awarded 2251 times.
Bending of an L-shaped beam
Awarded 5 hours ago
Difference between the tailboard and boot lid.
Awarded 12 hours ago
How to calculate external pressure resistance in spheres and cylinders?
Awarded 16 hours ago
How would you move a sail boat with no wind or paddles
Awarded 2 days ago
How to draw an arc through 2 known points and tangent to a line
Awarded May 25 at 13:42
Is there anything in BS 8888 regarding the scale of a section view?
Awarded May 24 at 19:55
Calculating torque in planetary gearbox
Awarded May 24 at 7:06
Force limits for gear rack and pinion gear
Awarded May 24 at 3:58
In the Panama Canal, how are the lock gates kept water-tight (at the hinges, middle, and bottom)?
Awarded May 21 at 20:17
deflection of mild steel hollow tube beam
Awarded May 19 at 11:01
How can I accurately measure the actuation force of small buttons (<1cm diameter) using home equipment?
Awarded May 18 at 13:11
Tension cable underneath rafter tie?
Awarded May 16 at 11:07
How much water do steam turbines consume per kWh of electricity generated?
Awarded May 15 at 10:27
Spring degradation in hand grip trainer
Awarded May 14 at 19:26
Where is the positive terminal on the laser pointer
Awarded May 14 at 14:25
Can lamda sensor 4.9 be used without the special LSU-IC?
Awarded May 13 at 13:25
Deflection of a rectangular plate simply supported (transverse load)
Awarded May 13 at 7:41
How to convert multiple point loads to uniformly distributed load
Awarded May 12 at 17:52
How to convert kN/m² into point loads?
Awarded May 11 at 6:40
What is the difference between plastic and compact cross sections?
Awarded May 9 at 12:03
How to determine optimal distance of rack and pinion?
Awarded May 9 at 1:28
Forward and Inverse Kinematics of PUMA 560
Awarded May 8 at 14:41
Force and Kinetic Energy on a Speed Bump
Awarded May 6 at 8:05
Solving Timoshenko beam equation for cantilever beam
Awarded May 5 at 21:10
What are typical forging loads?
Awarded May 5 at 5:17
How turbo engines increase efficiency if have lower compression ratio than naturally aspirated engines?
Awarded May 5 at 3:32
What is the purpose of digging up trench and then filling with something similar to asphalt crack filler?
Awarded May 4 at 14:17
Pull force on bolt
Awarded May 1 at 16:17
How do I compute combined tensile strength?
Awarded May 1 at 0:16
How to find yield strength and Young Modulus from S-S curve
Awarded Apr 30 at 5:12
In freecad, how do you copy a sketch geometry from one plane to another?
Awarded Apr 29 at 22:55
How to calculate the speed and force of the piston in a vacuum syringe?
Awarded Apr 27 at 13:15
Finding the reaction force at the hinge
Awarded Apr 25 at 10:16
Run this LED household lamp in a car?
Awarded Apr 20 at 22:17
Concentrated and Distributed loads in regards to moments
Awarded Apr 20 at 18:25
Calculating correct motor torque for windmill
Awarded Apr 19 at 2:16
How do you find the resultant hydrostatic force on a curved surface which is not exactly semicircle
Awarded Apr 18 at 19:21
Does ASME follow the ANSI standard, the ISO standard, or neither (both work)?
Awarded Apr 18 at 12:51
UDL vs Point Load on Truss
Awarded Apr 17 at 12:05
Should one use multiple elements through the thickness with multiple materials?
Awarded Apr 17 at 2:04
If a control system is unstable does it mean it will oscillate?
Awarded Apr 16 at 0:41
ANSYS: Why do I have a choice of choosing TOP/BOTTOM under contact/target shell faces?
Awarded Apr 14 at 20:22
Washers on both inside and outside?
Awarded Apr 14 at 18:32
How linear motion is getting converted into rotational motion in this early toy?
Awarded Apr 14 at 5:55
How do you determine flow distribution at a dividing T-Junction?
Awarded Apr 12 at 18:02
Multiple varying cross section beam with uniform loads
Awarded Apr 11 at 5:46
Please explain this flatbed microwave design
Awarded Apr 9 at 3:55
root locus of a system with two poles in the same place
Awarded Apr 7 at 1:31
Pole placement with damping ratio and natural frequency
Awarded Apr 4 at 13:26
Reverse vs Drive When Slipping Backwards
Awarded Apr 2 at 18:55
Shear coefficient for an I-Beam
Awarded Apr 1 at 19:10
What's a professional way of tracking design history in plant engineering?
Awarded Mar 31 at 8:26
How do i find the effective length factor (k) for a column from this chart?
Awarded Mar 31 at 5:55
Why is the normal stress assumed to be 0 in plane stress?
Awarded Mar 30 at 1:15
What did all those valves do in a U-Boat?
Awarded Mar 29 at 14:47
Why are bulldozers so slow?
Awarded Mar 28 at 5:20
Steel expanding in a tight space
Awarded Mar 27 at 15:20
shear flow in thin wall members
Awarded Mar 27 at 14:58
Sign convention for deflection and slope of beam?
Awarded Mar 23 at 12:47
Calculating tensile strength for aluminium
Awarded Mar 23 at 2:15
1
2 3 4 5
…
38

Your privacy

By clicking “Accept all cookies”, you agree Stack Exchange can store cookies on your device and disclose information in accordance with our Cookie Policy.