Engineering Beta

Teacher

 Teacher
Answer a question with score of 1 or more.
Awarded 1673 times.
How much force/torque act on a wheel of a vehicle when vehicle moves a constant speed and suddenly got a bump or jerk?
Awarded 6 hours ago
Punch Hole Exactly in Center of Acrylic
Awarded yesterday
Conventions regarding sliding and press-fit tolerances for shafts and bearings
Awarded May 14 at 19:21
Increasing torsional-stress resistance of an Auger at its motor-shaft joint
Awarded May 14 at 16:35
Increasing torsional-stress resistance of an Auger at its motor-shaft joint
Awarded May 14 at 2:42
How to determine the force to empty a syringe containing high-viscosity fluid?
Awarded May 10 at 21:35
Find minimum horizontal force required to keep the block and wedge stationary?
Awarded May 9 at 18:02
How can I achieve good diffusion from an LED light source?
Awarded May 7 at 3:06
What type of fastener is this? How does it work?
Awarded Apr 24 at 9:46
Difference in flow measurements in an open channel
Awarded Apr 18 at 21:51
Venturi Duct flow
Awarded Apr 17 at 12:43
(post deleted or otherwise unavailable)
Awarded Apr 17 at 12:43
Why not put servers in a refrigerator?
Awarded Apr 17 at 11:47
Why not put servers in a refrigerator?
Awarded Apr 16 at 19:39
Why not put servers in a refrigerator?
Awarded Apr 16 at 4:58
Why not put servers in a refrigerator?
Awarded Apr 15 at 21:43
Why not put servers in a refrigerator?
Awarded Apr 15 at 21:43
Is there any application of control engineering to the study of algorithms stability or computer science theory?
Awarded Apr 15 at 19:53
Conversion from LSB to mg not making sense for accelerometer
Awarded Apr 15 at 16:44
Why not put servers in a refrigerator?
Awarded Apr 15 at 9:59
How to manage two control loops as safety when BPCS is shared?
Awarded Apr 13 at 8:33
How to choose tolerance size?
Awarded Apr 11 at 8:32
Could an air compressor be used to compress steam?
Awarded Apr 11 at 6:35
What does “tempered water” exactly mean and how does it help cool the air?
Awarded Apr 7 at 6:55
How to Find the Magnitude of Force and Direction
Awarded Apr 5 at 2:03
What are the key technical challenges to development of traveling wave reactors?
Awarded Apr 2 at 18:55
Why are spur gear ratios not always whole numbers in practice?
Awarded Mar 30 at 22:15
Starter direction for methanol engine
Awarded Mar 30 at 18:46
Why is the All-In-Sustaining cost for mining gold so high relative to silver?
Awarded Mar 29 at 4:31
Software correction of CAD or Gcode based on machine measurements
Awarded Mar 26 at 15:33
Why doesn't epoxy stick to silicone?
Awarded Mar 24 at 16:12
Deflection Equation of a Stepped Beam
Awarded Mar 22 at 2:49
Unknown metal-piece connected to the case of an iPod Nano 2
Awarded Mar 21 at 16:48
How to evenly heat stainless type 304 steel bar to approximately 200F?
Awarded Mar 20 at 18:10
DWG specification document for parsing a DWG file?
Awarded Mar 17 at 20:27
Measuring distance to a non perpendicular surface
Awarded Mar 15 at 11:55
(post deleted or otherwise unavailable)
Awarded Mar 11 at 9:05
Modeling Vehicle Acceleration - Simulink
Awarded Mar 10 at 20:12
Why is the displacement gradient tensor equal to zero when the motion is pure shifting?
Awarded Mar 10 at 17:45
Small water pump powered by wind turbine : what type?
Awarded Mar 9 at 18:00
How to determine motor needed for water pump
Awarded Mar 9 at 12:57
Are there any instructions on how to install and run Natran-95?
Awarded Mar 9 at 10:46
vertical rack and pinion self-stopping
Awarded Mar 5 at 17:50
(post deleted or otherwise unavailable)
Awarded Mar 3 at 22:33
Is this dropout design as bad as I think?
Awarded Mar 3 at 22:33
Modeling Vehicle Acceleration - Simulink
Awarded Mar 3 at 21:50
Cooling tower for nuclear power plants
Awarded Mar 2 at 11:55
When I try to spin my stepper motor faster then 1000 pps, it vibrates and doesn't move
Awarded Feb 28 at 19:41
Why are some public benches made with arm rests that waste so much space?
Awarded Feb 28 at 4:04
Why are some public benches made with arm rests that waste so much space?
Awarded Feb 26 at 11:40
When designing scissors, how do you design the blade geometry to ensure good cutting capabilities?
Awarded Feb 23 at 16:20
Question on the determinacy of frame structures
Awarded Feb 20 at 17:05
DC Motors synchronization
Awarded Feb 20 at 10:16
Why do air entrainment admixtures improve the freeze-thaw resistance of concrete?
Awarded Feb 16 at 11:40
Transfer Function
Awarded Feb 16 at 7:36
I cannot properly understand the “pressure” referred to in Bernoulli's Principle despite my efforts
Awarded Feb 14 at 20:33
compression buckling of frame
Awarded Feb 13 at 23:55
Why aren't counterweights used more for garage doors?
Awarded Feb 12 at 15:56
Which way of solving from nonlinear control to choose?
Awarded Feb 8 at 10:11
What is “per unit strain”?
Awarded Feb 6 at 10:19
1
2 3 4 5
…
28

Your privacy

By clicking “Accept all cookies”, you agree Stack Exchange can store cookies on your device and disclose information in accordance with our Cookie Policy.